Since the 1980s, GE dishwashers have been diagnostic. If your Dishwasher detects a problem, an error code will appear on the screen. The error code is shown in the exact location of the numbers. A dishwasher error code indicates a particular problem. If your GE dishwasher isn’t working correctly, you may either look for a GE dishwasher repair on YouTube or call GE for instructions on fixing the device.
The latest General Electric (GE) Dishwashers feature advanced technologies designed to make life easier, but like any sophisticated appliances, they may occasionally run into issues. Specific error codes, such as C1, C2, C3, C4, C5, C6, C7, C8, and PF generally identify these issues. This article will demystify these codes and outline the steps to address each issue.
What does FTD mean on the Dishwasher screen?
FTD on Dishwasher means incorrect codes such as C1, C2, C3, C4, C5, C6, C7, C8, and PF. Below are all the faulty codes and steps you need to do to fix the problem.
Error Code – GE Dishwasher PF
The PF error code stands for Power Failure. This code appears when the Dishwasher has experienced a power interruption. Check if there was a recent power outage in your area or if the circuit breaker tripped. Resetting the Dishwasher by unplugging it for a few minutes and then plugging it back in can often resolve this issue.
Condition = Power fail error
Repair or Check = dishwasher fails. Home power may be out. Restart and run the Dishwasher.
Error C1 – GE Dishwasher
Error CondConditionraining Time Past 2 Minutes
Remove sink clogs, unplug the Dishwasher, clean the Dishwasher’s drain pipe, replace a damaged draining hose, check for a clogged drain pump, remove any obstructions, and replace a broken drain pump.
Error Code C1
This error code indicates a longer than usual fill time, possibly due to a low flow rate from the water supply. If your GE dishwasher displays this error, ensure your water supply valve is fully open. If the issue persists, the Dishwasher’s fill valve or water inlet may need service or replacement.
Error C2 – GE Dishwasher
This code indicates an issue with the water draining from the Dishwasher. There might be a clog in the drain line or a problem with the pump. Check your drain line for obstructions and clear them. If the problem continues, consider calling a professional to inspect the pump.
Error condition = 7-minute draining time
Remove sink clogs, unplug the Dishwasher, clean the Dishwasher’s drain pipe, replace a damaged draining hose, check for a clogged drain pump, remove any obstructions, and replace a broken drain pump. Press RESET to mute.
Drain Hose or Pump
GE Dishwasher – Error Code C3
The C3 error indicates that the Dishwasher cannot achieve the desired water temperature within the allotted time. Possible causes include a faulty heating element or a malfunctioning thermostat. Consult a trained technician for proper diagnostic and repair procedures.
Condition of error= Dishwasher Won’t Drain.
Repair or Check = Remove sink blockages. Unplug the Dishwasher. Clean the Dishwasher’s drain pipe. Replace a damaged draining hose. Check for a clogged drain pump. Remove any obstructions. Replace a broken drain pump.
Drain Hose or Pump
Error code C4 – GE Dishwasher
This code suggests an issue with the Dishwasher’s water circulation, possibly due to a blocked spray arm or a faulty pump. Check the spray arms for blockages, and if the problem is not resolved, call a professional to inspect the circulation pump.
Error condConditionishwasher is overfilled.
Cancel the wash cycle. After canceling, the Dishwasher won’t empty—C3 problem code troubleshooting. Check the overfill float if the dishwasher drains after canceling the wash cycle. If there’s nothing beneath the overfill float, unplug the Dishwasher and check the overfill float switch. Replace a broken overfill float switch.
Drain Pump, Drain Hose, Overfill Float Switch
Error code C5 – GE Dishwasher
The C5 error code signifies an issue with the Dishwasher’s temperature sensor. This typically requires professional help, as diagnosing and fixing a sensor issue can be complicated and should not be attempted without proper training.
Error condition = Dishwasher Doesn’t Have Enough Water (Drain Time Is Short)
Open the Dishwasher’s water supply valve. Ensure the Dishwasher’s overfill float switch isn’t stuck in the up position. Turn off the Dishwasher’s electricity and water. Check the water intake valve and fill line. If the intake screen is clogged, replace the water inlet valve; clearing the screen alone might cause flooding. Check the water intake valve harness for loose wires. If the water input valve doesn’t open, replace it.
Overfill Float Switch/Water Inlet Valve
Error code C6 – GE Dishwasher
This error signals that the Dishwasher’s heater is experiencing issues. These issues may include overheating or failing to heat. Since a replacement part is often needed, a professional should be contacted to address this issue.
Error condition = Too cold water (Water Not Hot Enough)
Turn on the sink’s hot water for 2 minutes. If the water is under 120F, adjust the water heater thermostat. You may break the sensor or control board if the Dishwasher’s water supply exceeds 120F.
Temperature sensor or electronic control board
Error code C7 – GE Dishwasher
The C7 error code indicates an issue with the Dishwasher’s motor. If you encounter this error code, you’ll likely need a professional to diagnose and potentially replace the motor.
Repair or Check = Water Temp Sensor Faulty 5-minute power outage
Powering down the board resets it. If error number C7 returns, plug in the Dishwasher. If so, unplug the Dishwasher and examine the water temperature sensor for loose connections. If the wiring is secure, replace the sensor. If the error returns, replace the control board.
Temperature sensor or electronic control board
Error code C8 – GE Dishwasher
This code signifies an issue with the detergent dispenser. Ensure the dispenser is not jammed or blocked with old detergent. If the problem persists, a professional service may be required to fix or replace the dispenser.
The blocked detergent dispenser cover
Repair = Unblock the dispenser lid. Close the dispenser and restart the Dishwasher. Check the cover 20-30 seconds into the cycle. If the detergent dispenser lid won’t open or it’s damaged, replace it.
Dispenser Assembly Replacement Parts
Opening of the cup
After adding the detergent, secure the cup since the detergent bottle has been left open. If there is a problem, the cycle will not start as usual. Tap the start pad once more if you do not want to proceed with opening the door.
A Leak Has Been Detected
There is evidence that there is a leak in the system.
The cycle will be terminated on models equipped with leak detection before it begins.
Frequently Asked Questions
- How can I tell whether the Dishwasher I have from GE has an FTD code?
Failure to drink is indicated by the acronym FTD in GE dishwashers. Examine the dishwasher drain tube, pump, and filter for any signs of clogging.
- What does the number 2 error code mean for my GE dishwasher?
Disconnecting the Dishwasher for thirty seconds may clear the error code. In rare circumstances, service may be necessary. GE Appliances Factory Service is in charge of any necessary repairs.
- My 1-year-old GE dishwasher has fault code FTD (Failure to Drain). How do I repair it?
Dishwashers won’t drain for numerous reasons. The filter or hose may be clogged. Dishwasher drain tubes feature a removable check valve. Remove the cap from the drain bar if you have installed or updated the trash disposal. Make sure there’s no partial cap left. Unsecured drain hoses might also cause problems. The drain hose should be pretty high to avoid dishwashing backup. Dish soap residue may clog drains. If you observe suds in the dishwasher water, that’s evidence of ordinary dish soap residue from pre-soaking dishes or a low drain hose causing dishwater to back up into the drain hose. It might potentially be a drain pump obstruction or failure.
When the Dishwasher hasn’t been emptied, start a cycle and cancel it. Remove the filter only if the Dishwasher is dry. Removing the filter may enable particles in the Dishwasher’s undrained water to harm or impede the pump. When you start a cycle, cancel it and wait 2 minutes. The water should drain, and you may clean the filter without dirt. Otherwise, the drain pump impeller may be fractured, or you may break it.
In conclusion, while some of these error codes might be resolved through simple checks and actions, most involve components that require professional intervention. It is always best to consult a trained technician to ensure safe and correct repairs to your GE dishwasher.
As an avid reader of cookbooks and professional chef blog posts, I will try to create helpful articles.
I enjoy researching different food industry topics such as sustainability in farming practices, health benefits of certain ingredients, food marketing tactics used by large companies, etc. This helps him stay informed on the latest nutrition news and develop a deeper understanding of how our food choices can directly impact our overall health and well-being.
As someone who truly values good quality food combined with nutritional awareness, I hope to inspire others by highlighting healthy food and offering the best deals from stores and restaurants.
- How Many Tablespoons is One Clove of Garlic? - June 26, 2024
- How to Measure 3/4 Cup When You Don’t Have the Right Measuring Cup? - June 6, 2024
- How Much Does Cooked Pasta Weight Compare To Dry? - April 30, 2024